OpenPilot CC3D EVO Flight Controller with Side Pins

Are you want to be an Electronic Geek in the future and going to build your own drone then this Flight controller is best for you. The flight controller uses the data gathered by the sensors to calculate the desired speed for each of the four motors.The flight controller sends this desired speed to the Electronic Speed Controllers (ESCs), which translates this desired speed into a signal that the motors can understand.

This OpenPilot CC3D EVO Flight Controller Side Pin card has a smooth feature that makes it directly compatible with satellite receivers without the need for any additional cables.It also supports S.BUS.Evo is equipped with a powerful 32-bit STM32 processor with 128kb Flash and 20kb RAM.The 3-axis MEMs technology is used for both gyro and accelerometer.

The OpenPilot CC3D EVO Flight Controller Side Pin card is easy to use with your computer.With USB and OpenPilot software, the card can be programmed in Windows, Mac, or Linux without the need for any drivers to install.OpenPilot is a very user-friendly program designed to be used by anyone, regardless of programming experience.

The OpenPilot CC3D EVO Flight Controller Straight Pin and OpenPilot CC3D EVO Flight Controller side Pinboards may not have any technical difference. There is only one difference between connector pins. (one has a Straight pin and the other have a 90 side pin.)

Note:

Please dont flash/Update the Default firmware.Updated or new firmware may cause a problem of connectivity with PC/Laptop.

To Explore more Flight Controller & Accessories, Click here

Specifications and Features :

CC3DEVO HardwareFeatures :

1. Runs as an App
2. Easy to use interface
3. Very intuitive setup Wizard
4. Evolving code
5. It Used to configure the board
6. It can run the multiple platforms
7. With a function of being directly plugged into the satellite receiver(It neednt conversion cable)
8. PowerfulSTM3232-bitmicrocontrollerrunningat90MIPswith128KBFlashand20KBRAM.
9. 3-axishigh-performanceMEMsgyrosand3-axishigh-performanceMEMsaccelerometer.
10. Tiny36 x 36 mm4layerPCBforsuperiorelectricalnoisereductionandflightperformance.
11. SoftwaresupportforWindows,Mac, andLinux.
12. Directhigh-speedUSBsupportwithnodriversrequired,atrueplugandplaydevice.
13. Spektrumsatellitereceiversupport.
14. FutabaS-BUShardwaresupport.
15. InnovativeFlexi-porttechnologyforsuperiorportflexibility.
16. 4Mbits on-board EEPROM for configuration storage.

Flexiport :

• Copter Control also offers the innovative Flexiport which provides either I2C connectivity or a second serial port. Flexiport gives Copter Control the flexibility to use either I2C and a single serial port or dual serial port, according to your connectivity needs.

Superioruserexperience :

1. OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally, for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with a bootloader already flashed.
2. A standard mini USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. The OpenPilot project, whilst still young, is trying to make Open Source much more user-friendly.
3. OpenPilotsoftwareisdesignedtobeusedbyeverybody!Allmajoroperatingsystemsaresupportedandinstallpackagesareprovided.
4. ThesoftwareisallFreesoftwareundertheGPLv3licenseandnotonlyareyouwelcometohackit,butweencourageit.

SensorsandComponents :

1. 3-axis Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2.
2. SupportsseveralcommonRCinputs:6PWMchannels,combinedPPM,Spektrum/JRDSM2, DSMJ,DSMXsatellites,andFutabaS.Busreceivers.
3. Simultaneoussupportformultiplereceivers.
4. ReceiverPortfunctions(configurable):6PWMinputchannelsorcombinedPPMstream,4PWMoutputchannels
5. MainPortfunctions(configurable):serialtelemetry(default),GPS,S.Bus,Spektrum/JRsatellites
6. FlexiPort(configurable):serialtelemetry,GPS,Spektrum/JRsatellites,orI2Cperipherals(under development)
7. 10PWMoutputstoservosorESCs,orforcamerastabilization
8. Camerastabilization supportsupto3axis cameramountswith stabilizationandmanual controlfromanyofconfiguredreceivers.
9. OnboardUSBconnectivityforeasyconfiguration.
10. USBandserialtelemetryandconfiguration
11. SupportedbypowerfulOpenPilotGCS
12. 4Mbitonboardmemory
13. 3CQuaternionbasedcomplementaryfilterrunningat500Hz

Package Includes :

1 x OpenPilot CC3D EVO Flight Controller with Side Pins
2 x Connecting Wires
1 x PC plastic shell

Tutorial Links :

Configure OpenPilot CC3D Evo